Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Sunrise
Gate repair in Sunrise needs to account for one thing most contractors miss: the air. Between the Atlantic on one side and the Everglades on the other, Sunrise sits in a pocket of brackish, salt-heavy humidity that corrodes gate hardware faster than almost anywhere else in Broward County. If your swing gate is sagging, your slide gate won’t close, or your opener board just died after a thunderstorm, we can usually get a technician to your Sunrise street the same day. Call (754) 354-2542 and you’ll get a written price before we touch a single bolt.
Why Calder Gate Repair Fort Lauderdale Is Sunrise’s Preferred Gate Repair Company
Calder Gate Repair works on gates all over Sunrise, from the older Welleby and Springtree neighborhoods to the gated communities off Nob Hill Road and the condo complexes near Sawgrass Mills. Our techs are background-checked, uniformed, and trained on nine major opener brands, including Sunrise Liftmaster service, so the same crew can fix the mechanical gate and the operator board in one visit. We’re part of the Relay Home Co. family, established 2009, and every job carries the 365-Day Done Right Promise: if a repair we make fails within a year, we come back and fix it at no charge.
What sets us apart in Sunrise specifically is that we know what this climate does to gates. We’ve pulled apart hinge posts near the Everglades that looked fine on the outside but were rusted through at the base. We know which operator boards survive afternoon lightning season and which ones don’t. Our Gate Repair team keeps stainless hardware and surge-rated components on the trucks because in this part of Sunrise, standard galvanized parts just don’t hold up.
Styles & brands we work with
Wrought Iron Gate Repair in Sunrise
Wrought iron gate repair in Sunrise is rarely about the iron itself; it’s about the joints, the hinge posts, and the welds that hold everything square. Salt-laden air works its way into every seam and pinhole. Within five to eight years, painted steel hinge posts can rust from the inside out, which is why a gate that looked level last spring suddenly drags the driveway in November. If we’re reinforcing a wrought iron gate here, we replace fasteners with stainless hardware and treat every weld with a rust-inhibiting coating before paint.
Hinge and Post Replacement
When a hinge post rusts through in Sunrise, tightening the hinge just buys you a few weeks. The post has to come out, and the new one needs a galvanized core or full stainless construction. We set posts in concrete with proper drainage so water doesn’t pool against the steel, which is what accelerates the rust cycle in the first place.
Weld Repair and Realignment
Wrought iron gates in Sunrise communities like Welleby often crack at the weld points where the gate leaf meets the hinge barrel. A clean weld is only half the job here; the gate also needs to be shimmed and realigned so the weight distributes evenly. Otherwise the new weld carries the entire load and fails again within a year.
Metal Gate Repair in Sunrise
Metal gate repair in Sunrise covers aluminum, steel, and mixed-material gates, and each one fails differently in this climate. Aluminum resists rust but warps under intense UV and heat, especially darker finishes. Steel is strong but corrodes fast in brackish air. We see a lot of aluminum slide gates binding on their tracks in Sunrise because the panel has bowed just enough to catch the guide rollers.
Slide Gate Track and Roller Work
Slide gates along Sunrise neighborhoods with exposed east-west exposure take direct afternoon sun, and that heat expansion is real. If the gate binds at 3 p.m. but runs fine at 8 a.m., the track spacing is too tight. We adjust roller brackets and re-set the track to allow thermal movement, which stops the mid-day binding without forcing the operator motor to work harder than it was designed to.
Frame Straightening and Panel Replacement
Sometimes the frame is still sound but the panel has warped beyond adjustment. In those cases, we’ll replace the panel and keep the existing frame if the steel is still structurally solid, which saves Sunrise homeowners several hundred dollars compared to a full gate replacement. New panels get a UV-stable finish rated for South Florida sun exposure.
Trusted Brands We Service in Sunrise
Our technicians are factory-familiar with the openers most common in Sunrise homes and HOA communities: BFT, Linear, Viking, Ghost Controls, and several others. We keep common control boards, limit switches, and replacement remotes stocked for Sunrise-area customers, which means we’re not waiting on a parts delivery when your BFT swing gate won’t close. If we don’t have the part, we can typically source it within one to two business days and schedule a return visit without a second diagnostic fee.
Common Gate Repair Problems We See in Sunrise Homes
- Rust-seized hinge posts in 1970s and 1980s gates: Original steel posts in gated communities and older single-family homes were installed before modern corrosion treatments. After decades of salt air, the post rusts at ground level and the gate tilts, putting strain on the opener. Replacement with galvanized or stainless posts is the permanent fix.
- Lightning-damaged operator boards after summer thunderstorms: Sunrise gets daily afternoon storms from June through September. A nearby strike can travel through the power line and take out the control board on a 1980s-era operator in seconds. Surge protectors installed at the board level significantly reduce this risk.
- Warped aluminum slide gates from UV exposure: Dark-finished aluminum panels absorb heat and can bow outward, which makes the gate catch on the track. This often reads as an opener problem when it’s actually a panel alignment issue.
- Failing keypad and intercom wiring in humid conditions: High humidity corrodes the low-voltage wiring connections in entry keypads and telephone entry systems. Symptoms include intermittent operation, buttons that work only when dry, or a gate that opens from the remote but not the keypad.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Sunrise, FL
For Sunrise residents, a typical gate repair service call runs $89 to $129 for the diagnostic and first hour of labor. Wrought iron hinge and post work generally falls between $350 and $900 depending on how many posts need replacing and whether new concrete is required. Metal gate realignment and roller replacement averages $250 to $600. Opener control board replacement, including a new surge protector, usually runs $400 to $900 before parts. Swapping in a new BFT or Viking opener starts around $1,100 installed. Every quote is in writing before work starts, and the number we quote is the number on your invoice. Call (754) 354-2542 for a free estimate.
We Also Serve Cities Near Sunrise
While we’re based out of Calder Gate Repair Fort Lauderdale, our technicians cover a wide radius around Sunrise. If you’re in Gate Repair in Sunrise or a neighboring city like Fort Lauderdale, Pompano Beach, Margate, or Hallandale Beach, we can get a tech to your gate quickly. The same written-price guarantee and 365-Day Done Right Promise applies everywhere we work.
Serving Sunrise, FL - Our Local Coverage Area
We’re based in the Sunrise area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Sunrise
Sunrise sits between two salt sources: the Atlantic Ocean to the east and the brackish Everglades to the west. That combination of salt air and high humidity penetrates painted steel hinges and posts far faster than the drier air inland cities like Plantation experience. A hinge that might last 15 years inland can seize in under 8 years here, which is why we recommend stainless hardware for any Sunrise replacement. Call (754) 354-2542 if your gate is starting to drag or bind.
Salt air corrodes the printed circuit traces and connection terminals inside operator control boards, which is why boards fail earlier in Sunrise than in inland Broward County. Corrosion builds on the board’s contacts and causes intermittent faults, like a gate that opens but won’t close, or a keypad that stops responding. We recommend a board-level surge protector and dielectric grease on all low-voltage connections as standard practice for Sunrise installations.
Yes, and we do it regularly. Many Welleby and Springtree communities still run original 1980s operators because the mechanical components remain sound. The common failure points are the control board, the limit switch, and the safety photocell wiring. We stock replacement boards for many older models and can often retrofit a modern surge-protected board into the existing housing, which costs less than a full operator replacement. If the motor itself is worn out, replacement is the honest recommendation.
The most common issue we see in Sunrise gated communities is a rusted hinge post that throws the gate out of square and trips the safety sensors. The gate then refuses to close or reverses mid-cycle, which residents often mistake for an electronic problem. We replaced a rust-seized swing gate hinge post in a Welleby community recently: the original FAAC operator was fine, but the corroded post footing had shifted everything out of alignment. A new galvanized post and stainless hardware solved it.
Yes. Florida’s building code requires entrapment protection on all automatic gates, which means functioning safety photocells, edge sensors, or both, plus a warning placard. If your gate was installed in the 1980s or 1990s, the original safety system may not meet current standards. We can retrofit modern UL-listed safety edges and photocells onto your existing gate and operator. Call (754) 354-2542 and we’ll inspect your setup and give you a written quote.
Call Calder Gate Repair for Gate Service in Sunrise
If your gate is sagging, binding, or just stopped working after last night’s storm, call (754) 354-2542 for our Gate Opener Repair in Sunrise. A live person answers around the clock, not a voicemail or a chatbot. We’ll give you a real arrival window, a written price before work begins, and the 365-Day Done Right Promise on every repair. Serving Sunrise from the Welleby area to Sawgrass Mills and everywhere in between.
Written by Nico Alvarez, Owner at Calder Gate Repair Fort Lauderdale.